Post by PAY UP $ SUCKER! on Jan 8, 2020 4:47:55 GMT -5
Weld compacts 2020
1) If you decide to push these rules you will be asked to fix or be loaded. NO REFUNDS! G 2) Rules are written to inspector’s interpretations, NOT the drivers. What the inspectors say goes. If the driver does not agree, they may load their cars.
G 3) IF IT DOES NOT SAY YOU CAN, THEN YOU CAN’T. Build at your own risk.
CAR PREP
CP 1) Remove all glass and outside trim.
CP 2) No flammable materials such as carpets, upholstery or headliners can be left in the car.
CP 3) Cars MUST be clean and free of loose objects inside the entire vehicle.
CP 4) Insulation blankets under the hood and in trunk MUST be removed.
CP 5) Wheel weights must be removed.
CP 6) Fuel tanks must be removed.
CP 7) 108″ wheel base or less( compact trucks ok)
CP No full size conversions ( NO Big cars smashed down to 108)
CP 9) May run mini Tucks and extended cabs
CP 10) May run V 8 motors
BUMPERS
B 1) Bumpers may be changed to any factory car bumper.
B 2) Bumper can be welded together cut and welded together
B 3) You can hard nose (no extra material).
B 4) You may stuff bumpers or build a bumper(MUST APPEAR TO BE STOCK) METAL ONLY
B 5) Can relocate in trunk only! IF you don’t run a rear bumper the bumper shocks MUST be removed!!!!!
B 6) May trim bumpers. When trimming off bumpers please keep people’s safety in mind.
B 7) Shocks can be collapsed and welded NO EXTRA MATERIAL.
B If you extend shocks. They must have a 1/4 hole for inspection! NO EXCEPTIONS! No homemade shock mount!
B 9) May have 2 Chains or 2 wraps of #9 wire, or two straps 2″ long or two cables 1/4″thick . NOT MORE THAN ONE that can go around bumper and around frame. ( Front and back) Maximum two wraps. No crossing allowed!
B 10) May weld rear bumper to trunk lid, may use 2″ strap.
FRAMES
F 1) May weld frame from transmission cross over forward top and bottom ALL WELDS NO WIDER THAN 3/4 inch!!!
F 2) May weld 12 more inches long and 3/4 inch wide, more top or bottom else where on both sides of frame .
F3) No extra metal, wood , foreign material and or concrete allowed in frame. NO FOAM IN FRAME
F 5) No frame to body welds!! NEED TO KEEP 1/4 GAP!
F 6) No Frame Pinning! No Frame Lacing!!
F 7) All frame holes must be open, No welding shut or washers added!! YOU PICK THE CARS WE DON’T!
F May tie frame rails together by rear end with chain or 2 raps of #9wire( no further foreward than hump)
F 9) Previous ran cars with broken or cracked frames may be re-welded where broken, but no farther than 2” (length) farther than crack in frame on either side of crack, no wider than 3/4 inch. Do not add filler material on weld and only one bead for cracks!! IF METAL IS ADDED THEN IT WILL COUNT AS ONE OF YOUR PLATES.
F 10) May pre-plate frames with plates, you may only use 6 total plates, 6 inch x 4 inches x 1/4 inch
F 11) No frame painting or undercoating or rhino linning to hide welds WILL NOT BE INSPECTED FOR SHOW!!!!
SUSPENSION
S 1) Rear coil springs can be changed , but must fit in stock location.
S 2) May chain rear differential to the floor or humps. (3/8 chain max.) or 2 wraps of # 9 wire per side NO PINNING!!
S 3) May reinforce A arms, must look like an A arm!! May weld or Bolt to frame. Or 4 1″ strap per A- arm
S 4) May reinforce stearing arms ( 1/4 inch material) or 2 inch angle iron.
S 5) May run modified rims no larger than 1/4 inch material . May modified rim, to allow for 16” tires.
S 6) No tire rule, but they must fit the car ( NO Monster Tires!!!)
S 7) 5″ x 5″ washer max for body bolt replacing top and bottom.
S No shock altering, over springs Ect.
BODY
B 1) Doors may be welded with no more than a 3″ stap solid. No wood, no foreign material or extra reinforcing allowed inside passenger doors.
B 2) Drivers’ doors must be welded shut. If door comes open driver will be disqualified from the heat. REINFORCEMENT MUST BE ADDED ON THE DRIVER’S DOOR, limited to 6” past edge of door, and MAY NOT protrude from car more than 2”. This door can be welded solid.
B 3) Only True grader blades allowed. No V blades.
B 4) DRIVER’S DOOR MUST HAVE ALL LATCHES OR SHARP OBJECTS REMOVED !!! HIGHLY RECOMEND PAD ON THE INSIDE!
B 5) Torn sheet metal in doors can be patched with sheet metal only 2″ lap, for safety reasons only!! 1/8 sheet metal only!
B 6) No filling in headlights with extra metal.
TRUNKS
T 1) Trunks may be welded solid or with a 3inch strap not both (NO ANGLE IRON). 1/4″ thick.
T 2) Trunk lids MUST have a 6 inch inspection hole. Station wagons must have rear deck plates removed!!
T 3) Minimal pre-bending of body is allowed, no full rear end wedges before car is ran. A pre-ran car may smash the trunk down for visibility reasons only.
T 4) Trunk may have two 1 inch all threads TOTAL and can be through the frame . A maximum 6”x6”x1/4” washer on trunk bolts
T 5) Trunk may be tucked into rear tail light cross brace, bend may start 10” back from end of trunk
HOODS
H 1) 100% of Hood must be removable. ( one hood only )
H 2) Hole must be cut in hood, large enough for fire extinguisher use.
H 3) A maximum of 8 bolts or all thread maybe used on the hood. Only four all threads TOTAL can go to frame.
H 4) The bolts shall be no more than 1” maximum. A maximum 6”X 6” washer on hood bolts.
H 5) You can weld together or bolt hood together with no more than 30 3/8 bolts and 1″ washers.
H 6) You are allowed to run two straps 2 inch wide 1/4 inch thick from core support to bumper or 2 wraps of # 9 wire or 1/4″ cable CHOOSE ONLY ONE!! No other reinforcing or added material to core support.
H 7) May weld all body seems under the hood ( fenders to fender wells ect.)
H You can weld fender to core support
H 9) NO inside seems may be welded in the drivers area or trunk !
H 10) May have 8 bolts per fender 3/8 inch max or weld.
H 11) For safety try to leave firewalls intact and heater core covered. Driver’s floor board must be in place. May cut for motor mod, but needs to have some cover!
H 12) Must have at least three front window bars in front of the driver can not be located directly behind distributor protector. May have two bars in back window NO larger 2 inch angle iron or pipe, (not welded to halo bar or 6″ past speaker lid or back window pillar).
H 13) All windows may have one 9-wire (2 wraps) or 1/4 cable(with one turn buckle) in one place not both!
DRIVERS COMPARTMENT
DC 1) A box (cage) around the driver and batteries is required. You are required to have at least a driver’s door bar, a bar from door post to door post, a dash bar and a bar from the dash bar to the door post bar on the passenger side.
DC 2) The 4 vertical bars ONLY can be welded to the frame or bolted to frame no more than 3 places per frame rail.
DC 3) You are allowed to run a vertical bar from the door to door bar of X-brace behind the seat straight up and connect to two together on top of the roof (roll bar). Located NO futher back than the middle of the back door behind driver!!
DC 4) No kickers from cage to frame with a distributor protector.. If you don’t run a protector you may have two kickers (one)per side 1/4 angle iron 6″ long.
DC 5) The only part of the cage allowed outside the car is the driver’s door and the bar across the roof.
DC 6) MUST HAVE INSIDE DOOR BAR FROM DASH TO SEAT BAR, TO PROTECT THE BATTERIES.
FUEL
F 1) Fuel tanks must be in the rear seat compartment and fastened securely.
F 2) Fuel tank size is a maximum 10 gallons (Metal or plastic boat gas tanks work very well.) Need cover (metal or inertube)
F 3) Fuel line must be connected with secure fittings. (Two clamps for every connector.)
F 4) Fuel line must be protected when passing though sheet metal.
F 5) No Alcohol!!
F 6) Fuel protectors CAN NOT be fastened to the back fire wall or have floor kickers!!
BATTERIES
B+ 1) Batteries must be moved to front seat compartment and fastened securelyB+ 2) Batteries must be covered for driver’s safety.B+ 3) Two batteries maximum or one cat battery may be used.DRIVE TRAINDT 1) Air cleaners must be left in place. All carburetors will have one.DT 2) Radiator must be left in place and no other water supply may be used.DT 3) May run 1/4″ expanded metal in front of radiator, welded in 4 (1″) spots. Cannot over lap metal by more than one 1″ of core support. No overlapping or welding to bumper.DT 4) May run radiator tank with pop off valve in place of a stock radiator.( Must Not Be used as enforcement)DT 5) You may run transmission coolers. They must be securely fastened.DT 6) No water engine cooled coolersDT 7) May run distributor protectorsDT May run engine cradles but they must be attached to the engine sub frame , transmission cross over and one other place.DT 9) Motor mounts can be welded down.DT 10) Radiator support can be in a U shape under frame but not strait frame rail to rail solid. Radiator support must support not reinforce, overlapping will be counted as plates!PAINTP 1) PAINT CAR NUMBER ON ROOF IN LARGE NUMBERS. Roof signs are recommended.B 2) PAINT DRIVERS NAME ON ROOF IN LARGE LETTERS.
DRIVER RULES
1. All drivers must have a valid drivers license and be at least 18 years of age. If not 18 years old, driver must have written permission and notarization from Parents or Guardians, Each driver and mechanic must sign a waiver releasing Outlaw Promotions from liability.
2. Helmets with face shields or helmets with goggles must be worn. (Safety glasses not considered as goggles or shield.) Long sleeved shirt or fire suit is required. NO SHORTS!
3. Seat belts must he worn. Shoulder harnesses are recommended.
4. Driver’s door hits and team driving will be decided by the judges.
5. Any door or hood coming open during race, that car will be removed from that heat.
6. Drivers must be present at drivers meeting held 30 min. before the show. Roll will be called.
7. Driver must make a hit at least every one minutes during race.
8. When call goes out for cars to be in place, drivers shall be in place and ready or will be disqualified from that heat.
9. Two wheels going over boundary line car will be disqualified!
10. Cars catching on fire 2 times in one heat will be disqualified from the heat.
11. ALL CARS WILL STOP IMMEDIATELY WHEN FLAGGED. (FOR FIRES, ETC.) OR THEY WILL BE BLACK FLAGGED.
12. All rulings by the Official Judge will be final.
13. Drivers must stay in car for safety reasons until the heat is over, except in case of fire.
14. ALL CARS ARE SUBJECT TO RE INSPECTION AT ANY TIME.
15. Judges may disqualify a car if it is deemed unsafe.
16. Drivers MUST accompany their car to the inspection. NO EXCEPTIONS.
17. Hood must be open for all inspections.
18. Roll overs are disqualified!!!
19) Must have Fire extinguisher inside
20) Official may drill before event and after at anytime!
1) If you decide to push these rules you will be asked to fix or be loaded. NO REFUNDS! G 2) Rules are written to inspector’s interpretations, NOT the drivers. What the inspectors say goes. If the driver does not agree, they may load their cars.
G 3) IF IT DOES NOT SAY YOU CAN, THEN YOU CAN’T. Build at your own risk.
CAR PREP
CP 1) Remove all glass and outside trim.
CP 2) No flammable materials such as carpets, upholstery or headliners can be left in the car.
CP 3) Cars MUST be clean and free of loose objects inside the entire vehicle.
CP 4) Insulation blankets under the hood and in trunk MUST be removed.
CP 5) Wheel weights must be removed.
CP 6) Fuel tanks must be removed.
CP 7) 108″ wheel base or less( compact trucks ok)
CP No full size conversions ( NO Big cars smashed down to 108)
CP 9) May run mini Tucks and extended cabs
CP 10) May run V 8 motors
BUMPERS
B 1) Bumpers may be changed to any factory car bumper.
B 2) Bumper can be welded together cut and welded together
B 3) You can hard nose (no extra material).
B 4) You may stuff bumpers or build a bumper(MUST APPEAR TO BE STOCK) METAL ONLY
B 5) Can relocate in trunk only! IF you don’t run a rear bumper the bumper shocks MUST be removed!!!!!
B 6) May trim bumpers. When trimming off bumpers please keep people’s safety in mind.
B 7) Shocks can be collapsed and welded NO EXTRA MATERIAL.
B If you extend shocks. They must have a 1/4 hole for inspection! NO EXCEPTIONS! No homemade shock mount!
B 9) May have 2 Chains or 2 wraps of #9 wire, or two straps 2″ long or two cables 1/4″thick . NOT MORE THAN ONE that can go around bumper and around frame. ( Front and back) Maximum two wraps. No crossing allowed!
B 10) May weld rear bumper to trunk lid, may use 2″ strap.
FRAMES
F 1) May weld frame from transmission cross over forward top and bottom ALL WELDS NO WIDER THAN 3/4 inch!!!
F 2) May weld 12 more inches long and 3/4 inch wide, more top or bottom else where on both sides of frame .
F3) No extra metal, wood , foreign material and or concrete allowed in frame. NO FOAM IN FRAME
F 5) No frame to body welds!! NEED TO KEEP 1/4 GAP!
F 6) No Frame Pinning! No Frame Lacing!!
F 7) All frame holes must be open, No welding shut or washers added!! YOU PICK THE CARS WE DON’T!
F May tie frame rails together by rear end with chain or 2 raps of #9wire( no further foreward than hump)
F 9) Previous ran cars with broken or cracked frames may be re-welded where broken, but no farther than 2” (length) farther than crack in frame on either side of crack, no wider than 3/4 inch. Do not add filler material on weld and only one bead for cracks!! IF METAL IS ADDED THEN IT WILL COUNT AS ONE OF YOUR PLATES.
F 10) May pre-plate frames with plates, you may only use 6 total plates, 6 inch x 4 inches x 1/4 inch
F 11) No frame painting or undercoating or rhino linning to hide welds WILL NOT BE INSPECTED FOR SHOW!!!!
SUSPENSION
S 1) Rear coil springs can be changed , but must fit in stock location.
S 2) May chain rear differential to the floor or humps. (3/8 chain max.) or 2 wraps of # 9 wire per side NO PINNING!!
S 3) May reinforce A arms, must look like an A arm!! May weld or Bolt to frame. Or 4 1″ strap per A- arm
S 4) May reinforce stearing arms ( 1/4 inch material) or 2 inch angle iron.
S 5) May run modified rims no larger than 1/4 inch material . May modified rim, to allow for 16” tires.
S 6) No tire rule, but they must fit the car ( NO Monster Tires!!!)
S 7) 5″ x 5″ washer max for body bolt replacing top and bottom.
S No shock altering, over springs Ect.
BODY
B 1) Doors may be welded with no more than a 3″ stap solid. No wood, no foreign material or extra reinforcing allowed inside passenger doors.
B 2) Drivers’ doors must be welded shut. If door comes open driver will be disqualified from the heat. REINFORCEMENT MUST BE ADDED ON THE DRIVER’S DOOR, limited to 6” past edge of door, and MAY NOT protrude from car more than 2”. This door can be welded solid.
B 3) Only True grader blades allowed. No V blades.
B 4) DRIVER’S DOOR MUST HAVE ALL LATCHES OR SHARP OBJECTS REMOVED !!! HIGHLY RECOMEND PAD ON THE INSIDE!
B 5) Torn sheet metal in doors can be patched with sheet metal only 2″ lap, for safety reasons only!! 1/8 sheet metal only!
B 6) No filling in headlights with extra metal.
TRUNKS
T 1) Trunks may be welded solid or with a 3inch strap not both (NO ANGLE IRON). 1/4″ thick.
T 2) Trunk lids MUST have a 6 inch inspection hole. Station wagons must have rear deck plates removed!!
T 3) Minimal pre-bending of body is allowed, no full rear end wedges before car is ran. A pre-ran car may smash the trunk down for visibility reasons only.
T 4) Trunk may have two 1 inch all threads TOTAL and can be through the frame . A maximum 6”x6”x1/4” washer on trunk bolts
T 5) Trunk may be tucked into rear tail light cross brace, bend may start 10” back from end of trunk
HOODS
H 1) 100% of Hood must be removable. ( one hood only )
H 2) Hole must be cut in hood, large enough for fire extinguisher use.
H 3) A maximum of 8 bolts or all thread maybe used on the hood. Only four all threads TOTAL can go to frame.
H 4) The bolts shall be no more than 1” maximum. A maximum 6”X 6” washer on hood bolts.
H 5) You can weld together or bolt hood together with no more than 30 3/8 bolts and 1″ washers.
H 6) You are allowed to run two straps 2 inch wide 1/4 inch thick from core support to bumper or 2 wraps of # 9 wire or 1/4″ cable CHOOSE ONLY ONE!! No other reinforcing or added material to core support.
H 7) May weld all body seems under the hood ( fenders to fender wells ect.)
H You can weld fender to core support
H 9) NO inside seems may be welded in the drivers area or trunk !
H 10) May have 8 bolts per fender 3/8 inch max or weld.
H 11) For safety try to leave firewalls intact and heater core covered. Driver’s floor board must be in place. May cut for motor mod, but needs to have some cover!
H 12) Must have at least three front window bars in front of the driver can not be located directly behind distributor protector. May have two bars in back window NO larger 2 inch angle iron or pipe, (not welded to halo bar or 6″ past speaker lid or back window pillar).
H 13) All windows may have one 9-wire (2 wraps) or 1/4 cable(with one turn buckle) in one place not both!
DRIVERS COMPARTMENT
DC 1) A box (cage) around the driver and batteries is required. You are required to have at least a driver’s door bar, a bar from door post to door post, a dash bar and a bar from the dash bar to the door post bar on the passenger side.
DC 2) The 4 vertical bars ONLY can be welded to the frame or bolted to frame no more than 3 places per frame rail.
DC 3) You are allowed to run a vertical bar from the door to door bar of X-brace behind the seat straight up and connect to two together on top of the roof (roll bar). Located NO futher back than the middle of the back door behind driver!!
DC 4) No kickers from cage to frame with a distributor protector.. If you don’t run a protector you may have two kickers (one)per side 1/4 angle iron 6″ long.
DC 5) The only part of the cage allowed outside the car is the driver’s door and the bar across the roof.
DC 6) MUST HAVE INSIDE DOOR BAR FROM DASH TO SEAT BAR, TO PROTECT THE BATTERIES.
FUEL
F 1) Fuel tanks must be in the rear seat compartment and fastened securely.
F 2) Fuel tank size is a maximum 10 gallons (Metal or plastic boat gas tanks work very well.) Need cover (metal or inertube)
F 3) Fuel line must be connected with secure fittings. (Two clamps for every connector.)
F 4) Fuel line must be protected when passing though sheet metal.
F 5) No Alcohol!!
F 6) Fuel protectors CAN NOT be fastened to the back fire wall or have floor kickers!!
BATTERIES
B+ 1) Batteries must be moved to front seat compartment and fastened securelyB+ 2) Batteries must be covered for driver’s safety.B+ 3) Two batteries maximum or one cat battery may be used.DRIVE TRAINDT 1) Air cleaners must be left in place. All carburetors will have one.DT 2) Radiator must be left in place and no other water supply may be used.DT 3) May run 1/4″ expanded metal in front of radiator, welded in 4 (1″) spots. Cannot over lap metal by more than one 1″ of core support. No overlapping or welding to bumper.DT 4) May run radiator tank with pop off valve in place of a stock radiator.( Must Not Be used as enforcement)DT 5) You may run transmission coolers. They must be securely fastened.DT 6) No water engine cooled coolersDT 7) May run distributor protectorsDT May run engine cradles but they must be attached to the engine sub frame , transmission cross over and one other place.DT 9) Motor mounts can be welded down.DT 10) Radiator support can be in a U shape under frame but not strait frame rail to rail solid. Radiator support must support not reinforce, overlapping will be counted as plates!PAINTP 1) PAINT CAR NUMBER ON ROOF IN LARGE NUMBERS. Roof signs are recommended.B 2) PAINT DRIVERS NAME ON ROOF IN LARGE LETTERS.
DRIVER RULES
1. All drivers must have a valid drivers license and be at least 18 years of age. If not 18 years old, driver must have written permission and notarization from Parents or Guardians, Each driver and mechanic must sign a waiver releasing Outlaw Promotions from liability.
2. Helmets with face shields or helmets with goggles must be worn. (Safety glasses not considered as goggles or shield.) Long sleeved shirt or fire suit is required. NO SHORTS!
3. Seat belts must he worn. Shoulder harnesses are recommended.
4. Driver’s door hits and team driving will be decided by the judges.
5. Any door or hood coming open during race, that car will be removed from that heat.
6. Drivers must be present at drivers meeting held 30 min. before the show. Roll will be called.
7. Driver must make a hit at least every one minutes during race.
8. When call goes out for cars to be in place, drivers shall be in place and ready or will be disqualified from that heat.
9. Two wheels going over boundary line car will be disqualified!
10. Cars catching on fire 2 times in one heat will be disqualified from the heat.
11. ALL CARS WILL STOP IMMEDIATELY WHEN FLAGGED. (FOR FIRES, ETC.) OR THEY WILL BE BLACK FLAGGED.
12. All rulings by the Official Judge will be final.
13. Drivers must stay in car for safety reasons until the heat is over, except in case of fire.
14. ALL CARS ARE SUBJECT TO RE INSPECTION AT ANY TIME.
15. Judges may disqualify a car if it is deemed unsafe.
16. Drivers MUST accompany their car to the inspection. NO EXCEPTIONS.
17. Hood must be open for all inspections.
18. Roll overs are disqualified!!!
19) Must have Fire extinguisher inside
20) Official may drill before event and after at anytime!